TNM7000 ECU-KIT Car Programmer is here!

TNM7000E 4-in-1 CAR Programmer is a universal tool for many purposes.

• ECU-KIT Software: ECU, Immobilizer, Dashboard programming through JTAG /ISP/BDM /GPT. OBD Cable Downloading.
• Universal programmer: Supporting 25000 Devices (Flash NOR/NAND/SPI, EEPROM, MCUs, CPLD and EMMC).
• ECU Remap software: ECU tuning + checksum calculation.
• CAN Analyzer software: for diagnosing CAR CAN-BUS problems and reverse engineering.

Free ECU-KIT car programming Software:

Supporting OBD/JTAG/ISP programming of Bosch, Delphi, Continental, Siemens, Denso, Mitsubishi, Valeo, Sagem, Magneti Marelli and many other units with wiring diagram and checksum calculation. Support of most MCUs Used in Car ECUs, Immobilizers, BCM, UCH, ABS, AirBag including:

Full Motorola (Freescale) 9S12 series with unsecure capiblity / Infineon Tricore TC17xx series with password reading for many ECUs / Hitachi SH705x read and write / Full Microchip PIC & DSPIC support / Full Atmel microcontrollers support / NXP PCF79xx remote chips / Renesas R5F10Dxx (Secured EEPROM read + Write) / NEC upd70F3xxx series  support / NEC UPD78F0828-937-949 Dashboard / NEC UPD78K0 Dashboard External/Internal EEPROM Read write through MBUS / Infineon XC233x, XC236x  MCUs used in AirBags / Fujitsu MB91F06x /Cypress S6J  & MB91F5xx MCUs used in Dashboards.

ISP Protocols: Tricore Boot /  Aurix TC27x JTAG / Bosch GPT (without ECU opening) / ST10F Boot Mode (Kline & ISP) / Motorola BDM with 9S12 Glitch security removal capability / Denso 76F00xx NBD  / MPC5XX BDM / JTAG MPC5XXX  / JTAG SPC56xx / Mitsubishi Boot / NEC MBUS / NXP FS32K142/144/146 / Renesas RH850 Unlock .

OBD Downloader and Reading with Checksum calculation (or Bench mode): 

• Bosch: BoschMe7 / BoschM7.8 / Bosch Me7.9.7 / Bosch Me17 China / Bosch Me17.9.7 / Bosch EDC17C53 / Bosch EDC17C39 / 4.5 (Flash&EEprom) / Bosch(Me7.4.4 Flash&EEprom) / Bosch M7.4.4 / Bosch M7.4.9 /  Bosch M7.4.11 / Bosch MG1CS1 / Bosch CPGDSH2
• Bosch for Bikes: Bosch MSE3.0 / Bosch MSE6.0 / Bosch MSE8.0 / Bosch MSE2.0 (MG1CA094)
• Continental: Hyundai & Kia SIM2K250 / SIM2K260 / SIM2K251 / Sim2K-141 / Sim2K-24x / Sim2K-34x / Renault EMS3132 (Flash & EEPROM) / EMS3134.
• Cummins for trucks: CM2150 / CM2220 /CM554 / CM876
• Delphi:Delphi MT92.1 / Delphi MT62.1 / Delphi CRD2.35 / Delphi MT86 / Delphi MT38 / Delphi MT60 / Delphi MT80 / Delphi MT22.3 / Delphi MT22 / Delphi MT22.1 / Delphi MT20U2 / Delphi MT05-1 / Delphi MT05-2/ Delphi MT05-3
• Denso for Toyota: GEN 1 + virtual online read + CUW converter / Gen2-P5CAN
• Hitachi: Nissan (2005-2018)
• Mitsubishi: Mazda3/6 (E6T6xxxx), Mazda3 (E6T5xxx)
• SAGEM: Renault S3000 / Peugeot S2000
• Valeo: Peugeot PL4 / J34 /J35

Remap and ECU Tuning: 

Remap Tables and 2D & 3D Views + Checksum calculation.

Programmer Software:

25000 Supported Devices Flash Memory (Parallel / Nand /Serial), EPROM, EEPROM, Serial EEPROM, Microcontroller, NVRAM, FRAM, PLD).

• 48-Pins ZIF Socket with Pin Continuity tester & 10-Pins ISP/JTAG Connector.
• USB 2.0 High Speed, Read EMMC /Nand Flashes with 12Mbyte/Sec, Reading Serial Flash memory with 8 Mbit/Sec.
• Auto detection of all flash Memories/Microcontrollers with Device ID.
• Multiple Programming is possible by attaching 2 or more Programmers to one PC.

Additional Features:

• Low cost adapters, works with many different adapters from other programmers.
• Free software upgrade with no Subscription Fee. Windows XP/VISTA/7/8/10/11 (32, 64 bits) Support.